Image 1 of 1
Image 1 of 1
Image 1 of 1
Image 1 of 1
DEWATERING AND CORROSION
PREVENTATIVE FLUIDS
APPLICATIONS
The PDW range of products are specially formulated de-watering solutions finding many applications in
the engineering automotive and aerospace industries for ; manufactured parts in transit, temporary
protection between operations, moulds, spares and parts in storage, removal of droplets from decorative
surfaces.
PDW/S - conforms to milspec-c-16173 Grade 3.
This heavy duty dewatering/protective removes water from metal surfaces and leaves a dry non-tacky
deposit for clean handling. The easily removable deposit gives up to 6 months protection when stored
internally and up to 1 months protection when stored externally from rust and corrosion. On request
batches can be manufactured to include a dye which helps to identify parts which have been treated.
PDW/A
Similar to PDW/S but with less heavy deposit to give up to 3 months internal protection for parts in store or
between machining operations etc.
PDW/B
A non-residual dewatering fluid to disperse moisture and droplets of water from decorative plated metal
surfaces. A few days of inhibition on steel is obtained between machining operations etc.
METHOD OF USE
The PDW range are used as supplied in immersion tanks made of galvanised steel. Larger objects may
be sprayed (not suitable when using PDW/B).
TANKS:- The solution should be placed in a tank, the base of which should be angled at about 350. At
its lowest point a tap should be inserted from which water is drawn off at regular intervals to maintain the
efficiency of the product. Immerse components in the solution for 5-15 minutes, remove and allow to drain
over the tank for a short while. Finally allow components to stand until completely dry, which can take up
to 3 hours depending on the product used. Periodically drain-off the water that collects in the bottom of
the tank.
SPRAY:- Apply the solution with a spray gun to give a liberal coating. If too little is applied by this
method the water will not be flushed off the surface, causing further corrosion problems.
SAFETY PRECAUTIONS
Products are flammable, keep away from naked flames or sources of ignition. (Note: The dry films formed
are non-flammable). Avoid inhalation, use in well ventilated areas. Wear appropriate protective clothing.
Wash off skin contacts with plenty of water. In cases of eye contact irrigate with plenty of clean water and
seek medical attention. For detailed health and safety information request hazard data sheets.
PACKAGING 25 litre drums.
DEWATERING AND CORROSION
PREVENTATIVE FLUIDS
APPLICATIONS
The PDW range of products are specially formulated de-watering solutions finding many applications in
the engineering automotive and aerospace industries for ; manufactured parts in transit, temporary
protection between operations, moulds, spares and parts in storage, removal of droplets from decorative
surfaces.
PDW/S - conforms to milspec-c-16173 Grade 3.
This heavy duty dewatering/protective removes water from metal surfaces and leaves a dry non-tacky
deposit for clean handling. The easily removable deposit gives up to 6 months protection when stored
internally and up to 1 months protection when stored externally from rust and corrosion. On request
batches can be manufactured to include a dye which helps to identify parts which have been treated.
PDW/A
Similar to PDW/S but with less heavy deposit to give up to 3 months internal protection for parts in store or
between machining operations etc.
PDW/B
A non-residual dewatering fluid to disperse moisture and droplets of water from decorative plated metal
surfaces. A few days of inhibition on steel is obtained between machining operations etc.
METHOD OF USE
The PDW range are used as supplied in immersion tanks made of galvanised steel. Larger objects may
be sprayed (not suitable when using PDW/B).
TANKS:- The solution should be placed in a tank, the base of which should be angled at about 350. At
its lowest point a tap should be inserted from which water is drawn off at regular intervals to maintain the
efficiency of the product. Immerse components in the solution for 5-15 minutes, remove and allow to drain
over the tank for a short while. Finally allow components to stand until completely dry, which can take up
to 3 hours depending on the product used. Periodically drain-off the water that collects in the bottom of
the tank.
SPRAY:- Apply the solution with a spray gun to give a liberal coating. If too little is applied by this
method the water will not be flushed off the surface, causing further corrosion problems.
SAFETY PRECAUTIONS
Products are flammable, keep away from naked flames or sources of ignition. (Note: The dry films formed
are non-flammable). Avoid inhalation, use in well ventilated areas. Wear appropriate protective clothing.
Wash off skin contacts with plenty of water. In cases of eye contact irrigate with plenty of clean water and
seek medical attention. For detailed health and safety information request hazard data sheets.
PACKAGING 25 litre drums.