Image 1 of 1
Image 1 of 1
Image 1 of 1
Image 1 of 1
PCS202
CONCENTRATED CARBONISED OIL AND PAINT REMOVER
PCS202 Is formulated for the removal of oil and petroleum product which have been
exposed to high temperatures forming a carbonaceous deposit. PCS202 also strips
paint finishes. PCS202 is a two-phase liquid. The lower phase contains a powerful
blend of chlorinated tar acid solvents and wetting agents whilst the upper phase
contains corrosion inhibitors. Components are immersed in the solvent phase, which
Softens and loosens deposits and paints films, and then withdrawn through the
corrosion inhibited upper phase. Corrosion of treated parts is subsequently minimised.
The water seal also reduces solvent losses and minimises vapour levels in the working
environment. The product can also be supplied without the water seal. For this request
PCS 204.
APPLICATIONS
PCS202 is suitable for use on all metals. PCS202 is use cold in soak tanks and is
particularly suited to many reconditioning and maintenance cleaning operations,
removing carbon, fuel residues, tar, paint and resin from various engine, machine,
motor, compressor and burner components.
METHOD OF USE
To ensure correct proportions of upper and lower phase in use solutions, always either
shake drum thoroughly prior to decanting or use whole drum quantities. The product
is used as supplied and should not be heated. Use in a mild steel tank. To ensure an
economical bath life, heavily soiled parts should be degreased prior to PCS202
processing and where paint is removed, a sludge tray should be included in the soak
tank design. Components should be immersed in the solvent layer until deposits or
paint are loosened (normally 0.5 to 2 hours), then carefully withdrawn through the
water seal and pressure rinsed to remove remaining residues.
PCS202 can also be used in enclosed systems and can be circulated by means of a
suitable pump and an external reservoir. The product is used neat and should not be
allowed to exceed a temperature of 60`c. Depending on the type of deposit to be
removed a circulation time of 4 to 24 hours is required. After treatment flush the unit
with water, steam or flushing oil.
PRECAUTIONS IN USE
PCS202 will adversely affect many plastics, including Perspex, acrylics, polystyrene
and A.B.S resins. PCS202 will also cause distortion and swelling of rubber materials,
and will damage varnish and paint finishes.
SAFETY PRECAUTION
*FOR PROFESSIONAL USE ONLY*
Always use PCS202 in a well ventilated area. Avoid contact with skin and eyes. Wash
any splashes off with soap and water. For detailed health and safety information
request a hazard data sheet
PACKAGING 25 and 205 litre drums.
PCS202
CONCENTRATED CARBONISED OIL AND PAINT REMOVER
PCS202 Is formulated for the removal of oil and petroleum product which have been
exposed to high temperatures forming a carbonaceous deposit. PCS202 also strips
paint finishes. PCS202 is a two-phase liquid. The lower phase contains a powerful
blend of chlorinated tar acid solvents and wetting agents whilst the upper phase
contains corrosion inhibitors. Components are immersed in the solvent phase, which
Softens and loosens deposits and paints films, and then withdrawn through the
corrosion inhibited upper phase. Corrosion of treated parts is subsequently minimised.
The water seal also reduces solvent losses and minimises vapour levels in the working
environment. The product can also be supplied without the water seal. For this request
PCS 204.
APPLICATIONS
PCS202 is suitable for use on all metals. PCS202 is use cold in soak tanks and is
particularly suited to many reconditioning and maintenance cleaning operations,
removing carbon, fuel residues, tar, paint and resin from various engine, machine,
motor, compressor and burner components.
METHOD OF USE
To ensure correct proportions of upper and lower phase in use solutions, always either
shake drum thoroughly prior to decanting or use whole drum quantities. The product
is used as supplied and should not be heated. Use in a mild steel tank. To ensure an
economical bath life, heavily soiled parts should be degreased prior to PCS202
processing and where paint is removed, a sludge tray should be included in the soak
tank design. Components should be immersed in the solvent layer until deposits or
paint are loosened (normally 0.5 to 2 hours), then carefully withdrawn through the
water seal and pressure rinsed to remove remaining residues.
PCS202 can also be used in enclosed systems and can be circulated by means of a
suitable pump and an external reservoir. The product is used neat and should not be
allowed to exceed a temperature of 60`c. Depending on the type of deposit to be
removed a circulation time of 4 to 24 hours is required. After treatment flush the unit
with water, steam or flushing oil.
PRECAUTIONS IN USE
PCS202 will adversely affect many plastics, including Perspex, acrylics, polystyrene
and A.B.S resins. PCS202 will also cause distortion and swelling of rubber materials,
and will damage varnish and paint finishes.
SAFETY PRECAUTION
*FOR PROFESSIONAL USE ONLY*
Always use PCS202 in a well ventilated area. Avoid contact with skin and eyes. Wash
any splashes off with soap and water. For detailed health and safety information
request a hazard data sheet
PACKAGING 25 and 205 litre drums.